Top Curve
Symbol
 
 
EVAC50W24V EVAC50W24V
Pertronic Industries' 50W 24V Amplifier has been designed to generate the Evacuation tone and verbal message as specified by NZS 4512:2003. The EVAC50W24V is capable of driving up to 50W of power via PA loud speakers such as the Pertronic PSS1 and PSSB501. Any of the standard tones may be replaced with one of 44 custom tones.
     
  Listen to Custom Tones below.

Tone 01 Evacuation Tone with Voice
Tone 02 Evacuation Tone
Tone 03 Alert Tone with Voice
Tone 04 Alert Tone
Tone 05 T3 Cadence with Voice
Tone 06 T3 Cadence
Tone 07 Simulated Bell Tone
Tone 08 PA400 Tone
Tone 09 Claxon (star trek)
Tone 10 400-700Hz 1.5 sec whoop
Tone 11 800/100Hz @ 1Hz sweeping
Tone 12 400/450Hz @ 0.5 Hz tone
Tone 13 2400/2900Hz 7 Hz - sweeping
Tone 14 2400/2900Hz 1 Hz - sweeping
Tone 15 500/1200Hz @ 1 Hz - sweeping
Tone 16 1200/2900Hz @ 2 Hz - alternating
Tone 17 2400/2900Hz @ 2 Hz alternating
Tone 18 1000 Hz @ 1Hz - intermittent
Tone 19 800/1000Hz @ 0.875 Hz - alternating
Tone 20 2400 Hz @ 1Hz intermittent
Tone 21 800Hz 0.25s on, 1s off - intermittent
Tone 22 800Hz - continuous
Tone 23 660Hz 150mS on/off - intermittent
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
Tone 24 544 (100mS) / 440 Hz(400mS) - NF S 32-001
Tone 25 660 Hz 1.8s on, 1.8s off - intermittent
Tone 26 1.4 kHz - 1.6kHz 2Hz
Tone 27 660Hz - continuous
Tone 28 544Hz / 440 Hz - alternating
Tone 29 544 @ 0.875s - intermittent
Tone 30 800Hz @ 2Hz - intermittent
Tone 31 800 / 1000Hz @ 25Hz - sweeping
Tone 32 2400 / 2900 @ 25Hz - sweeping
Tone 33 554Hz - continuous
Tone 34 440Hz - continuous
Tone 35 800 / 100Hz @ 7Hz- sweeping
Tone 36 660 / 1200Hz @ 1Hz- sweeping
Tone 37 2 Tone Chime 1000/650 Hz
Tone 38 745Hz @ 1Hz - intermittent
Tone 39 1000 & 2000Hz @ 0.5s alternating
Tone 40 1000Hz continuous - PEEER Toxix Gas
Tone 41 2000Hz - continuous
Tone 42 1200Hz - continuous
Tone 43 800Hz/1000Hz @ 4HZ alternating
Tone 44 RH3 Tone 500Hz – 1400 Hz @ 5Hz repetition
Tone 45 'SOS' in Morse code
Tone 46 300Hz - 1400Hz - 300Hz Sweep
Tone 47 3480Hz 130mS on/off
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
(mp3)
  These tones are indicative of the amplifier tones and may vary slightly from actual sound



Evac Generator Module EVACGEN-NZ
Pertronic Industries' Evac Generator Module extends the F100A and F120A analogue addressable automatic fire alarm system by allowing a fully monitored interface between the control panel and a 3rd party 100Vrms amplifier of up to 250W output. It has four selectable inputs, each of which can be programmed to produce different tones when activated. Two of the tones may include a voice message.



EVAC20W24V EVAC20W24V
Pertronic Industries' 20W 24V Amplifier has been designed to generate the Evacuation tone and verbal message as specified by NZS 4512:2003. The EVAC20W24V is capable of driving up to 20W of power via PA loud speakers such as the Pertronic PSS1 and PSSB501.
  Listen to Evacuation Tone with Voice



EVAC20W12V EVAC20W12V
Pertronic Industries' 20W 12V Amplifier has been designed to generate the Evacuation tone and verbal message as specified by NZS 4512:2003. The EVAC20W12V can be directly mounted into the Pertronic F4 conventional fire alarm panel but can also be used with any 12V fire alarm system, and is capable of driving up to 20W of power via PA loud speakers such as the Pertronic PSS1 and PSSB501.
 
  Listen to Evacuation Tone with Voice



EVAC120W24V Amplifier EVAC120W24V 120W Amplifier
This amplifer is designed for use in emergency evacuation systems. It is powered by an external 24Vdc (nominal) power source. The amplifier accepts linelevel audio inputs and produces a 100V line output via a transformer.



EVAC250W24V EVAC250W24V 250W Amplifier
This amplifer is designed for use in emergency evacuation systems. It is powered by an external 24Vdc (nominal) power source. The amplifier accepts linelevel audio inputs and produces a 100V line output via a transformer.



EVAC50W24V Preamp Board EVAC50W24V Preamp Board
Pertronic Industries' 50W Amplifier Preamp is a piggyback board designed to enable the connection of a public address or fire microphone to the Pertronic Industries 50W Amplifier.



PREAMP-RB Preamp Board PREAMP-RB Preamp Board
The Redback A2055 Pre-amplifier module may be used to boost the input level to the Pertronic 50W Amplifier Pre-amp board in situations where the microphone is connected at distances too great to operate at microphone level input or where the microphone input is feeding more than four amplifiers.



ADM-2-PMB-125 Audio Distribution Module 2-Way
The Pertronic Audio Distribution Module (ADM-2-PMB125) creates a pair of independently monitored 100 Vrms audio lines (channels). This module simplifies the provision of two separate audio channels covering one area or evacuation zone.
A system built with an ADM-2-PMB125 will continue operating even if one channel develops a fault.
Also available as a PCB only (without case).




ADM-4 Audio Distribution Module 4-Way
The Pertronic Audio Distribution Module 4-Way (ADM-4) provides multiple independently controlled and monitored 100 VRMS audio lines (channels). Several ADM-4 modules may be connected to a single amplifier, providing four switchable audio channels per ADM-4. This simplifies audio system installations by allowing four or more spurs from a single 100 Volt audio line without compromising the defect monitoring system.



EVACHMIC EVACHMIC
The EVACHMIC is a balanced EWIS Hand Microphone. Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord. Tailored frequency response is 300Hz - 8kHz.



EVACDMIC EVACDMIC (CO0379)
The EVACDMIC balanced Desk Microphone has a tapered low frequency response for articulate speech reproduction and enhanced clarity.


Bottom Curve